Safety is a Lifestyle

What is required at each stage of PLAN-DO-CHECK-ACT Or PDCA? We’ll have a look at the theory at each stage and then see how to use the principles in practice by introducing a new piece of equipment. PLAN This stage covers two key issues: planning for implementation and policy. It is all about the P’s – PLANNING and POLICY. Planning for implementation means identifying where we are now and then identifying where we want to be. For example, we could be looking at introducing a new piece of equipment into our workplace. So what should we be considering at this stage? How are we going to control the risks associated with this equipment? What is the most suitable equipment from a safety perspective? What emergency procedures need to be put in place? What are the training requirements? Is any personal protective equipment required? During this stage we should also make sure that we are meeting the requirements of our organisation’s Health and Safety Policy. ...

Direct Costs are just the tip of the iceberg. Direct, or insured costs for accidents are usually considered those costs covered by workers compensation insurance and other minor medical costs for the accident. The company pays insurance to cover these costs. The average direct costs depend on the nature of the injury or illness, but usually range from $1,000 to $20,000. A good round figure to use when estimating all lost time workplace injuries is $10,000. Of course, the more accidents, the higher the insurance. Indirect costs....what they can do to your company. Indirect costs are all the "uninsured" additional costs associated with an accident. What is important to realize is that indirect costs are usually much greater than direct costs: From 2-10 times as expensive. Another important point is that, unlike direct costs, indirect costs are uninsured...they come right out of the corporate pocketbook. These are the costs that can drive a company into the red. The NS...

Why safety is not a priority for many organisations putting people's lives at risk?? Leakage of Styrene gas in Vishakhapatnam      A bad reminder of Bhopal Gas tragedy, A major toxic gas leakage at LG Polymers near Gopalapatnam region of Visakhapatnam in the early hours of Thursday on 7-May-2020 killed at least Nine people, while affecting hundreds in some 20 villages in around three kilometre range, where the condition of dozens was said to be critical. NOTE: Residents are advise of in and around Gopalapatnam   - Don't panic , drink excess water, clean the face with wet cloth frequently and cover the   nose with wet cloth or mask What is styrene? what are the precautions?          It is a flammable liquid that is used in the manufacturing of polystyrene plastics, fiberglass, rubber, and latex. According to Tox Town, a website run by the US National Library of Medicine, styrene is also found in vehicle exhaust, cigarette s...

The hierarchy starts with the controls perceived to be most effective and moves down to those considered least effective. It flows as follows: Elimination  – Physically remove the hazard Substitution  – Replace the hazard Engineering controls  – Isolate people from the hazard Administrative controls  – Change the way people work Personal protective equipment – Protect the worker by using PPE “You can’t eliminate every hazard, but the closer you can get to the top, the closer you can reach that ideal and make people healthier and safer,.           Hierarchy of Hazard Control  पदानुक्रम सबसे प्रभावी माना जाने वाले नियंत्रणों से शुरू होता है और कम से कम प्रभावी माना जाता है। यह इस प्रकार है: उन्मूलन - शारीरिक रूप से खतरे को हटा दें प्रतिस्थापन - खतरे को बदलें इंजीनियरिंग नियंत्रण - लोगों को खतरे से अलग करना प्रशासनिक नियंत्रण - लोगों के काम करने के तरीके को बदलें व्यक्तिगत सुरक्षा उपकरण- पीपीई का उपयोग करके कार्यकर्ता क...